MA5616(config)# time 2009-06-12 14:45:30 设置系统时间，根据实际情况设置
MA5616(config)# sysname MA5616 设置系统名称，根据实际情况设置
MA5616(config)# vlan 100 smart 网管VLAN 100
MA5616(config)# vlan 3450 to 3481 mux 业务VLAN，VLAN类型为MUX
MA5616(config)# vlan 3803 smart 窄带业务VLAN
MA5616(config)# port vlan 100 0/0 1 在上行口透传VLAN
MA5616(config)# port vlan 3450 to 3481 0/0 1
MA5616(config)# port vlan 3803 0/0 1
MA5616(config)#interface vlanif 100 配置网管地址
MA5616(config-if-vlanif100)# ip address 10.41.236.26 255.255.255.0
MA5616(config-if-vlanif100)#quit
MA5616(config)#interface vlanif 3803 配置窄带地址
MA5616(config-if-vlanif3803)# ip address 10.47.143.173 255.255.255.224
MA5616(config-if-vlanif3803)#quit
MA5616(config)# ip route-static 0.0.0.0 0.0.0.0 10.41.236.1 宽带路由
MA5616(config)# ip route-static 10.3.35.0 255.255.255.128 10.47.143.161 窄带路由
MA5616(config)#multi-service-port 建立宽带业务流
{ from-vlan<K>|vlan<K> }:from-vlan
{ vlanid<U><1,4093> }:3450
{ board<K>|port<K> }:board
{ frame-id<K>|num-list<S><Length 1-255> }:4 根据宽带板实际位置选择
{ autosense<K>|inbound<K>|rx-cttr<K>|user-8021p<K>|user-encap<K>|user-vlan<K>|vp
i<K> }:vpi 设置宽带的VPI和VCI值，跟MODEM一致，济南一般VPI为0，VCI为100；
{ vpi<U><0,255> }:0
{ vci<K> }:vci
{ vci<U><32,255> }:100
{ inbound<K>|rx-cttr<K>|single-service<K>|user-8021p<K>|user-encap<K>|user-vlan<
K> }:rx-cttr 6 tx-cttr 6
Command:
multi-service-port from-vlan 3450 board 4 vpi 0 vci 100 rx-cttr 6 tx-cttr 6
MA5616(config)# adsl line-profile
{ add<K>|delete<K>|modify<K>|quickadd<K>|quickmodify<K> }:add
{ <cr>|profile-index<U><2,125> }:2
Command:
adsl line-profile add 2
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the profile (y/n) [n]:y
> Please input profile name:ADSL_4M
> Please choose default value type 0-adsl 1-adsl2+ (0~1) [0]: 0
> Will you set basic configuration for modem? (y/n)[n]:Y 无需修改可以选择N
Note: Setting to these mode of G.992.3~5 will lead that the adsl ports that
are not support adsl2+ not be activated
> ADSL transmission mode:
> 0: All (G.992.1~5,T1.413)
> 1: Full rate(G.992.1/3/5 or T1.413)
> 2: g.lite(G.992.2/4) (ADSL over ISDN board doesn't support g.lite mode)
> 3: T1.413(ADSL over ISDN board doesn't support T1.413 mode)
> 4: g.dmt (G.992.1/3/5)
> 5: g.hs (G.992.1~5, G.992.5 is prior)
> 6: G.992.1
> 7: G.992.2(ADSL over ISDN board doesn't support G.992.2 mode)
> 8: ADSL all (G.992.1~2,T1.413)
Please select (0~8) [0]:
> Trellis mode 0-disable 1-enable (0~1) [1]:
> Downstream channel bit swap 0-disable 1-enable (0~1) [0]:
> Upstream channel bit swap 0-disable 1-enable (0~1) [0]:
> Please select channel mode 0-interleaved 1-fast (0~1) [0]:
> Will you set interleaved delay? (y/n)[n]:y 无需修改可以选择N
> Maximum downstream interleaved delay(0~255 ms) [6]:
> Maximum upstream interleaved delay(0~255 ms) [6]:
> Please select form of transmit rate adaptation in downstream:
> 0-fixed 1-adaptAtStartup (0~1) [1]:
> Will you set SNR margin for modem? (y/n)[n]:y 无需修改可以选择N
> Target SNR margin in downstream(0~31 dB) [6]:
> Minimum SNR margin in downstream (0~6 dB) [0]:
> Maximum SNR margin in downstream (6~31 dB) [31]:
> Target SNR margin in upstream (0~31 dB) [6]:
> Minimum SNR margin in upstream (0~6 dB) [0]:
> Maximum SNR margin in upstream (6~31 dB) [31]:
> Will you set parameters for rate? (y/n)[n]:y
> Minimum transmit rate in downstream (32~8160 Kbps) [32]:
> Maximum transmit rate in downstream (32~8160 Kbps) [6144]:4096 根据实际情况选择，此处选择为4096，即用户带宽为4M。
> Minimum transmit rate in upstream (32~896 Kbps) [32]:
> Maximum transmit rate in upstream (32~896 Kbps) [640]:
Add profile 2 successfully
MA5616(config)#interface adsl 0/4
MA5616(config-if-adsl-0/4)#deactivate
{ all<K>|portid<U><0,31> }:all
Command:
deactivate all
Deactivate port 0 successfully
MA5616(config-if-adsl-0/4)#activate all 激活新的4M模板
{ <cr>|profile-index<K>|profile-name<K> }:profile-index 2
Command:
activate all profile-index 2
Send the command to activate port 0 successfully
MA5616(config)# voip 配置窄带数据
MA5616(config-voip)# ip address media 10.47.143.173 10.47.143.161
MA5616(config-voip)# ip address signaling 10.47.143.173
MA5616(config-voip)# quit
MA5616(config)# interface h248 0 配置H248接口数据
MA5616(config-if-h248-0)# if-h248 attribute mgip 10.47.143.173 mgport 2944 transfer udp
MA5616(config-if-h248-0)#if-h248 attribute primary-mgc-ip1 10.3.35.4 primary-mgc-port 2944
MA5616(config-if-h248-0)#if-h248 attribute secondary-mgc-ip1 10.3.35.68 secondary-mgc-port 2944
MA5616(config-if-h248-0)# if-h248 attribute mg-media-ip1 10.47.143.173
MA5616(config-if-h248-0)# if-h248 attribute start-negotiate-version 1
MA5616(config-if-h248-0)#quit
MA5616(config)#esl user 添加窄带用户
MA5616(config-esl-user)#mgpstnuser batadd 0/3/0 0/3/63 0 terminalid 0 ste
p 1 telno 88880000
880020170991(config-pstnport)#pstnport attribute batset 设置窄带宽口为反极性
{ frameid/slotid/portid<S><Length 1-15> }:0/3/0
{ endframeid/slotid/portid<S><Length 1-15> }:0/3/63
{ clip-reverse-pole-pulse<K>|dial-mode<K>|line-lock<K>|nlp-mode<K>|polarity-reve
rse-mode<K>|reverse-pole-pulse-level<K>|reverse-pole-pulse<K> }:reverse-pole-pul
se enable
{ <cr>|clip-reverse-pole-pulse<K>|dial-mode<K>|line-lock<K>|nlp-mode<K>|polarity
-reverse-mode<K>|reverse-pole-pulse-level<K> }:reverse-pole-pulse-level
{ level-value<U><20,1270> }:1000 polarity-reverse-mode
{ polarity-mode<E><hard-polarity-reverse,soft-polarity-reverse> }:soft-polarity-
reverse
{ <cr>|clip-reverse-pole-pulse<K>|dial-mode<K>|line-lock<K>|nlp-mode<K> }:
1
发表于 2010-5-6 16:23:40