经验 69 分贝 0 家园分 87 在线时间: 22 小时 最后登录: 2016-4-9 帖子: 22 精华: 0 注册时间: 2009-1-8 UID: 319217
注册:2009-1-8
AWS常用操作
1、
create the ISAM node
NE à create...
Type 设备类型 7300 ATM设备型号为ASAM-LAEU 、7300 IP设备型号为 ASAM-FENT 、
7325 设备型号为 7325RU - NBEU、
7302 isam 设备型号为 ISAM - LEEU
7302
FD 设备型号为 ISAM – LNEU
Name 为当前需创建的节点名称
NE IP Address
为当前设备IP地址
其他默认即可
节点删除的方法:选中该节点
NE –Supervision – Stop
等节点为红色箭头朝下的时候 在 NE –Delete
即可.
节点的改名字的方法: 将该节点删除重新创建即可
2、
Create the board
n
Board à create...
n
Create LT board:EALT-A
Board Type
为当前用户板卡型号
7302 设备和 7325 设备的用户板卡不需要软件支持 而 7300 设备在创建板卡的时候要根据主控板的软件版本选择相应的软件 .
3 、Create a new subscriber
(1)Create two profiles (service profile and spectrum profile) and download
to ISAM
n
Create XDSL Spectrum profile
Fill out the profile name and only select ADSL Operational Modes ( POTS).
Keep the default parameter on other pages
n
Create XDSL Service profile
Fill out the name and speed.
Notes: Select ‘ No Interleaving ‘ for
ADSL fast mode
n
Download two profiles ( XDSL Spectrum , XDSL Service ) to ISAM
Select this two profiles, add to the blank , then press ‘OK’
以下是 7302 用户端口配置
( 2 ) Click in the board window, Port -> Port -> Configure…
Administrative State: Unlock
Select the define profiles
OK 即可
(3) Create ATM PVC
Connection->Create->ATM termination...
输入 VPI and VCI
8 :35
(4)Binding VLAN to PVC(create Ethernet connection)
n
Residential Bridge mode: 所有用户一个VLAN的创建方法
Connection->VLAN Association->Residential Bridge VLAN->Configure...
选择相应的VLAN ID 即可 (例 VLAN ID 200)
Cross connect mode: 一个用户一个VLAN的创建方法
Connection->VLAN Association->Cross Connect VLAN->Configure...
输入 C_VLAN id and C_VLAN Name
输入端口号对应的VLAN ID (例VLAN ID 100)
OK 即可
以下是 7325 用户端口配置
( 1 ) Click in the board window, Port -> Port -> Configure…
ok 即可
(2) Create ATM PVC
Connection->Create->Ethernet Connection
不要点OK
继续点左上角的 ATM 弹出下面菜单
ok 即可
7325 在网管修改业务VLAN 范围的方法
Service -> Vlan ->RB VLAN id
Ranges ->Configure
修改相应参数
OK即可
切记 修改完业务VLAN范围以后必须重起节点,修改才能生效。
在网管上重起节点的方法:
Supervision
-> NE Reset
->Without Self Tset
-> ok
7325 创VLAN
You can create vlan according to following scenario.
(1) Select the node.
(2) Service->Definition->Create->Residential Bridge VLAN...
(3) Enter Service Name.
(4) Select "Shared, with VLAN id, enter vlan id.
(5) Select "Ready for use" at the bottom of this dialog window.
(6) Servide->Deployment->Deploy
Select the vlan name which you added and click OK.
(7) Now you can create XC with vlan parameter.