通信人家园

标题: 烽火路由器基本配置命令 [查看完整版帖子] [打印本页]

时间: 2014-2-2 16:48

作者: yanjunqi 标题: 烽火路由器基本配置命令

Router#show controller s1/0

Interface Serial1/0

Hardware is PowerQUICC MPC860T

SCC Registers:

General [GSMR]=0x68034:0x22, Protocol-specific [PSMR]=0x3000

Events [SCCE]=0, Mask [SCCM]=0xcf, Status [SCCS]=0x3

Transmit on Demand [TODR]=0, Data Async [DSR]=0x7e7e

Interrupt Registers:

[CICR]=00e49f80 [CIPR]=4000c006 [CIMR]=48000000, [CISR]=00000000

Command register [CR]=0x6c0

SICR=0900002c, BRG=00000000:00010288:00000000:00000000 (aux=0)

Statistics: scc4, port3

int 751229 bad_first 0 too_long 0 drop 0

tx_count 1 bk_count 0 h_Q 81 s_Q 0

Port A [PADIR]=0000 [PAPAR]=53c3 [PAODR]=0000 [PADAT]=fefe

Port B [PBDIR]=00021001 [PBPAR]=00001020 [PBODR]=0000 [PBDAT]=0001e3be

Port C [PCDIR]=0000 [PCPAR]=0008 [PCSO]=0438 [PCDAT]=0fe7 [PCINT]=0008

Receive Ring

rmd(fff02320): status=9000 length=0000 address=01155f58

rmd(fff02328): status=9000 length=0000 address=01156c90

rmd(fff02330): status=9000 length=0000 address=01156b18

rmd(fff02338): status=9000 length=0000 address=011569a0

rmd(fff02340): status=9000 length=0000 address=01156828

rmd(fff02348): status=9000 length=0000 address=011566b0

rmd(fff02350): status=9000 length=0000 address=01156538

rmd(fff02358): status=b000 length=0000 address=01156f80

Transmit Ring

tmd(fff02360): status=0000 length=0000 address=00000000

tmd(fff02368): status=0000 length=0000 address=00000000

tmd(fff02370): status=0000 length=0000 address=00000000

tmd(fff02378): status=0000 length=0000 address=00000000

tmd(fff02380): status=0000 length=0000 address=00000000

tmd(fff02388): status=9000 length=0051 address=01156df4

tmd(fff02390): status=0000 length=0000 address=00000000

tmd(fff02398): status=2000 length=0000 address=00000000

SCC GENERAL PARAMETER RAM (at 0xfff03f00)

Rx BD Base [RBASE]=0x2320, Fn Code [RFCR]=0x15

Tx BD Base [TBASE]=0x2360, Fn Code [TFCR]=0x15

Max Rx Buff Len [MRBLR]=252

Current Rx(2) State [RSTATE]=0x9000, BD Ptr [RBPTR]=0x1156b18

Current Tx(5) State [TSTATE]=0x9000, BD Ptr [TBPTR]=0x1156df4

SCC UART PARAMETER RAM (at 0xfff03f30)

Maximum idle characters 1

Break Character 1

Received Parity Error 58445

Received Frame Error 65261

Received Noise Error 39256

Number of break conditions 22595

Last Received Break length 1524

uart1 63220 uart2 1

Transmit Out of sequence 0

cc[0] = 4011 cc[1] = 4013 cc[2] = 8000 cc[3] = 4011

cc[4] = 4013 cc[5] = 8000 cc[6] = 9c80 cc[7] = 7051

rccm = c0ff rccr = bf28 rlbc = a6fe

RxBufSiz 254 flow 1

flag=00000120, size=00000008, X=11, Xoff=13

DCR_B3#

通信人家园 (https://www.txrjy.com/)