通信人家园

标题: ZX9800开局手册  [查看完整版帖子] [打印本页]

---

时间:  2010-8-31 21:14

作者: kokoe01     标题: ZX9800开局手册

Login:admin
用户名
Password:admin 密码
fsap>en
Please input password:
Admin
密码
fsap# erase configuration
清空
Are you sure to erase: [N]y
fsap# reboot
重起
Are you sure to reboot system? Press Y to confirm or another key to exit: [N]y
fsap# add-card asnvb 2 self-shelf
添加用户板件当分离器板件和用户板件在一框里时用self-shelf
fsap# add-card vTNEI 4 self-shelf
添加用户板件
fsap# add-card asnvb 7 splitter-shelf添加用户板件当分离器板件有单独的机框时用splittler-shelf
fsap# add-card atnGB 6
添加用户板件 当用户板件和分离器板件合成一起时直接添加

注：没有添加用户板件时show card命令查不到任何板件，只能现场观看用户板件类型后进行添加，当添加用户板件类型不匹配时板件不会启动，当用show card命令查看板件状态由starting 转变为work时说明板件正常工作。


fsap# show card slot 9
用此命令查看上联子卡的类型
Rack No
: 1
Shelf No
: 1
Slot No
: 9
Status
: Main/SubCardMismatch
Hard Type
: CSCA
Row State
:
Soft Version
: V1.0.5o
Hard Version
: 68
Create Time
: 20060427101110
Upside subcard
: NONE/Mismatched/TGFC
上槽位上联子卡的类型
Underside subcard
: NONE/Mismatched/SGFB
下槽位上联子卡的类型
fsap# add-subcard csc up tgfc un sgfb
给主控板添加上联网络的子卡
fsap# configure




fsap(config)# add-vlan 200,300
添加用户、管理VLAN
fsap(config)# mac-address-table aging-time 300
设置MAC地址的老化时长
fsap(config)# mac inband 00:d0:d0:06:07:10
设置带内MAC地址
fsap(config)# adsl-profile _4m

创建速率文件
fsap(config)# adsl-profile _4m
修改参数速率文件配置
AtucConfRateMode(1-fixed,2-adaptAtStartup,3-adaptAtRuntime):[2]
AtucConfRateChanRatio(0..100):[0]
AtucConfTargetSnrMgn(0..310(0.1dB)):[80]
AtucConfMaxSnrMgn(80..310(0.1dB)):[310]
AtucConfMinSnrMgn(0..80(0.1dB)):[0]
AtucConfDownshiftSnrMgn(0..310):[0]
AtucConfUpshiftSnrMgn(0..310):[0]
AtucConfMinUpshiftTime(0..16383):[0]
AtucConfMinDownshiftTime(0..16383):[0]
ConfProfileLineType(1-fast-only ,2-interleaved-only):[2]
AtucChanConfFastMaxTxRate(0..102400kbps):[1024]4096
AtucChanConfFastMinTxRate(0..4096kbps):[0]
AtucChanConfInterleaveMaxTxRate(0..102400kbps):[1024]4096
AtucChanConfInterleaveMinTxRate(0..4096kbps):[0]
AtucChanConfMaxInterleaveDelay(0..255ms):[16]
AturConfRateMode(1-fixed,2-adaptAtStartup,3-adaptAtRuntime):[2]
AturConfRateChanRatio(0..100):[0]
AturConfTargetSnrMgn(0..310(0.1dB)):[80]
AturConfMaxSnrMgn(80..310(0.1dB)):[310]
AturConfMinSnrMgn(0..80(0.1dB)):[0]
AturConfDownshiftSnrMgn(0..310(0.1dB)):[0]
AturConfUpshiftSnrMgn(0..310(0.1dB)):[0]
AturConfMinUpshiftTime(0..16383):[0]
AturConfMinDownshiftTime(0..16383):[0]
AturChanConfFastMaxTxRate(0..10240kbps):[512]1024
AturChanConfFastMinTxRate(0..1024kbps):[0]

AturChanConfInterleaveMaxTxRate(0..10240kbps):[512]1024
AturChanConfInterleaveMinTxRate(0..1024kbps):[0]
AturChanConfMaxInterleaveDelay(0..255ms):[16]
AtucDMTConfFreqBinsOperType(1-open,2-cancel):[2]
AturDMTConfFreqBinsOperType(1-open,2-cancel):[2]
LineDMTConfEOC(1-byte ,2-streaming ):[1]
LineDMTConfTrellis(1-on,2-off):[1]
AtucConfMaxBitsPerBin(0..15):[15]
AtucConfTxStartBin(6..511):[32]
AtucConfTxEndBin(32..511):[511]
AtucConfRxStartBin(6..63):[6]
AtucConfRxEndBin(6..63):[31]
AtucConfUseCustomBins(1-on,2-off):[2]
AtucConfDnBitSwap(1-on,2-off):[2]
AtucConfUpBitSwap(1-on,2-off):[2]
AtucConfREADSL2Enable(1-on,2-off):[2]
AtucConfPsdMaskType(1-DMT_PSD_MSK,2-ADSL2_PSD_MSK,3-ADSL2_READSL_WIDE_PSD_MSK,4-ADSL2_READSL_NARROW_PSD_MSK):[2]
AtucConfPMMode(1-DISABLE,2-L2_ENABLE,3-L3_ENABLE,4-L3_ENABLE | L2_ENABLE):[1]
AtucConfPML0Time(0..255s):[240]
AtucConfPML2Time(0..255s):[120]
AtucConfPML2ATPR(0..31db):[3]
AtucConfPML2Rate(512..1024kbps):[512]
Press M or m key to modify, or the other key to complete?[C]
fsap(config)# slot adsl 2
进入单板槽位
fsap(cfg-slot-adsl-2)# pvid 200 pvc 1
配置端口的PVID
fsap(cfg-slot-adsl-2)# trap-control en
打开端口上报功能
fsap(cfg-slot-adsl-2)# atm pvc 1 vpi 0 vci 35
配置端口的modem的pvc植
fsap(cfg-slot-adsl-2)# no shutdown 打开端口
fsap(cfg-slot-adsl-2)# adsl profile _4m
给用户端口设置速率
fsap(config)# ip subnet 136.38.34.XXX 255.255.255.000 300
设置带内的IP 300为管理VLAN
fsap(config)# snmp-server host 136.38.34.2
设置网管服务器的IP
fsap(config)# ip route 0.0.0.0 0.0.0.0 136.38.34.1
设置路由
fsap(config)# vlan 200 2/1-64 untag 把用户端口绑定到用户VLAN里
fsap(config)# vlan 200 4/1-24 untag

fsap(config)# vlan 200 6/1-32 untag
fsap(config)# vlan 200 9/1 tag
把上联口绑定到用户VLAN 里
fsap(config)# vlan 300 9/1 tag
把上联端口绑定到管理VLAN 里
fsap(config)# slot ethernet 9
fsap(cfg-slot-eth-9)# up-link 1 设置所有用户隔离起用PVLAN
fsap# save 保存数据



fsap(config)# interface gigabit-ethernet 9/2
fsap(cfg-if-ge-9/2)# pvid 200
fsap(config)# vlan 200 9/2 untag



[ 本帖最后由 commspec 于 2010-10-11 19:51 编辑 ]

---

通信人家园 (https://www.txrjy.com/)

Powered by C114