通信人家园

标题: 如何将华为MA5626配置Vlan中继链路变成普通三层交换机使用 [查看完整版帖子] [打印本页]

时间: 2022-6-17 15:20

作者: yanqiu18 标题: 如何将华为MA5626配置Vlan中继链路变成普通三层交换机使用

文章来源：裕普网络
南充裕普网络教你如何将华为MA5626配置Vlan中继变成普通三层交换机使用，简单分为三步。MA5626是华为技术有限公司推出的远端光接入单元。MA5626支持FTTB、FTTC组网应用，为小区用户提供语音、数据和视频业务接入。这就是它与普通交换机的区别。
第一步，清除MA5626交换机配置。命令如下
用户名：root
密码：mduadmin （这是默认的用户名和密码）
登陆MA5626后输入清除数据命令
enable ---回车
erase flash data ---回车
Y ---回车
然后输入重启命令
reboot system---回车
Y---回车
第二步，创建VLAN和VLAN业务模板，将我们所创建的VLAN加入VLAN业务模板中。
1、分别创建两个VLAN
huawei(config)#vlan 2 smart
huawei(config)#vlan 658 smart
2、创建VLAN业务模板
huawei(config)#vlan service-profile profile-id 1
huawei(config-vlan-srvprof-1)#forwarding vlan-mac    //VLAN转发模式：VLAN+MAC地址（vlan-mac）
huawei(config-vlan-srvprof-1)#bpdu tunnel enable    //打开二层网桥协议报文透传开关
huawei(config-vlan-srvprof-1)#user-bridging enable    //打开二层网桥协议开关
huawei(config-vlan-srvprof-1)#commit    //使用commit命令进行提交才能使配置生效
huawei(config-vlan-srvprof-1)#quit
3、将绑定VLAN与VLAN业务模板
huawei(config)#vlan bind service-profile 2 profile-id 1    //使用vlan bind service-profile命令将配置完成的VLAN业务模板与VLAN进行绑定
huawei(config)#vlan bind service-profile 658 profile-id 1

第三步，配置电口0/1/1为中继，使用service-port命令建立中继端口。将0/1/2-0/1/4配置为VLAN658的access口。将0/1/7-0/1/8配置为VLAN2的access口。
1、创建0/1/1业务虚端口为trunk中继，其中对应user-vlan为658，S-VLAN为658，业务流模板为6。另一个对应user-vlan为2，S-VLAN为2，业务流模板为6。
huawei(config)#service-port vlan 658 eth 0/1/1 multi-service user-vlan 658 rx-cttr 6 tx-cttr 6
huawei(config)#service-port vlan 2 eth 0/1/1 multi-service user-vlan 2 rx-cttr 6 tx-cttr 6
2、将0/1/2-0/1/4配置为VLAN658的access口。
huawei(config)#service-port vlan 658 eth 0/1/2 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6
huawei(config)#service-port vlan 658 eth 0/1/3 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6
huawei(config)#service-port vlan 658 eth 0/1/4 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6
3、将0/1/7-0/1/8配置为VLAN2的access口。
huawei(config)#service-port vlan 2 eth 0/1/7 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6
huawei(config)#service-port vlan 2 eth 0/1/8 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6

完整配置如下

MA5626(config)#

MA5626(config)#display current-configuration
{ <cr>|port<K>|section<K>|service-port<K>|simple<K>||<K> }:

  Command:
      display current-configuration
[MA5626V800R312: 2300]
#
[device-config]
  <device-config>
port port-index 0/0/1 port-type GPON-PORT
#
[public-config]
  <public-config>
snmp-agent local-engineid 800007DB0304B0E7C38D1606
#
[vlan-config]
  <vlan-config>
vlan 2 smart
vlan 20 smart
vlan 658 smart
#
[vlan-srvprof]
  <vlan-srvprof>
vlan service-profile profile-id 1 profile-name "srvprof-1"
  bpdu tunnel enable
  user-bridging enable
  commit
vlan bind service-profile 2 profile-id 1
vlan bind service-profile 658 profile-id 1
#
[eth]
  <eth-0/0>
interface eth 0/0
network-role 1 cascade
#
[gponnni]
  <gponnni-0/0/1>
interface gponnni 0/0/1
password "%5L3_.^M^.9I<V@WN#JI1!!B#A8&)VAB']]F;U$19'2_1!!B#A8&)VAB']]F;U$19'
2_1!!%"
loid "%VL*&O__.3U3;RaK'0`"NPQ!!,DWUN(I=,'UZ_`@1RI<=WQ!!%"
checkcode "%L9;7+FT2-[LX3NU/Va@a]Q!!%"
#
[bbs-config]
  <bbs-config>
service-port 0 vlan 2 eth 0/1/1 multi-service user-vlan 2 inbound traffic-table index 6 outbound traffic-table index 6
service-port 1 vlan 658 eth 0/1/1 multi-service user-vlan 658 inbound
traffic-table index 6 outbound traffic-table index 6
service-port 2 vlan 658 eth 0/1/2 multi-service user-vlan 658 inbound
traffic-table index 6 outbound traffic-table index 6
service-port 3 vlan 658 eth 0/1/3 multi-service user-vlan 658 inbound
traffic-table index 6 outbound traffic-table index 6
service-port 4 vlan 658 eth 0/1/4 multi-service user-vlan 658 inbound
traffic-table index 6 outbound traffic-table index 6
service-port 5 vlan 2 eth 0/1/7 multi-service user-vlan 2 inbound traffic-table index 6 outbound traffic-table index 6
service-port 6 vlan 2 eth 0/1/8 multi-service user-vlan 2 inbound traffic-table index 6 outbound traffic-table index 6
service-port 7 vlan 2 eth 0/1/8 multi-service user-vlan untagged inbound
traffic-table index 6 outbound traffic-table index 6
service-port 8 vlan 2 eth 0/1/7 multi-service user-vlan untagged inbound
traffic-table index 6 outbound traffic-table index 6
service-port 9 vlan 658 eth 0/1/2 multi-service user-vlan untagged inbound
traffic-table index 6 outbound traffic-table index 6
service-port 10 vlan 658 eth 0/1/3 multi-service user-vlan untagged inbound
traffic-table index 6 outbound traffic-table index 6
service-port 11 vlan 658 eth 0/1/4 multi-service u ser-vlan untagged inbound
traffic-table index 6 outbound traffic-table index 6
service-port 12 vlan 20 eth 0/1/1 multi-service user-vlan 20 inbound
traffic-table index 6 outbound traffic-table index 6
#
[abs-config]
  <abs-config>
config
#
[prevlanif]
  <prevlanif>
interface vlanif20
#
[vlanif]
  <vlanif20>
interface vlanif20
ip address 192.168.1.83 255.255.255.0
#
[meth]
  <meth0>
interface meth0
ip address 10.11.104.2 255.255.255.0
#
[null]
  <null0>
interface null0
#
[aaa]
  <aaa>
aaa
authentication-scheme "default"
#
authorization-scheme "default"
#
accounting-scheme "default"
#
domain "default"
#
local-user "admin" password ""JZU.+!OI+_=EA>*VG'J!!!"
local-user "admin" privilege level 2
#
return

时间: 2024-1-8 14:19

作者: annbv

你好，上行光口怎么配置，我一直没有搞通

通信人家园 (https://www.txrjy.com/)